Side-Power 8980 Manuale di Installazione Pagina 15
- Pagina / 28
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
15
LOCATION 130: ENABLING THE SWINGER SHUTDOWN
Location 130 is used to enable the burglary zone swinger shutdown. The number programmed in this location will
determine the number of trips the Ranger 8980 will allow, before bypassing all burglary zones (1-8) which have tripped
during an arming cycle. The bypassed zones will not report trips to a central station, and the local siren or bell will not
sound for these zones. A zone trip will not be added to the number count until after the zone has tripped more than
once. If this location contains a "0", this feature is disabled. A zone which has been bypassed by this feature will be
reported if bypass reporting is enabled in location 125. NOTE: If Immediate Restore By Zone is enabled in
Location 137, multiple reports may be transmitted during a siren cycle without adding to the trip count.
LOCATION 131: AUTOMATIC BYPASS / INSTANT ARMING
Location 131 is used to enable automatic "Instant Arming". Programming a "1" in this location will cause the control to
automatically enter the "Instant" mode and bypass interior follower zones if a fault is not detected on an entry/exit zone
during the exit delay. Programming a "3" in this location (Automatic Bypass), will cause the interior follower zones to
become bypassed if a fault is not detected on an entry/exit zone, yet will not change the status of the entry/exit zone. If
this location contains a "0", these features are disabled. Pressing the [r] key when the system is armed, will cause the
"Instant" light to toggle. When the "Instant" light is on, the entry/exit zone is instant; when off, the entry/exit zone is
delayed. The [r] key will toggle the "Instant" mode regardless of the programming data in this location.
LOCATION 132: BUILT-IN SIREN DRIVER / 1 AMP VOLTAGE OUTPUT
The built-in siren driver has a steady sound (for Priority zone type), and a yelp sound (for Burglary and Panic). Factory
default is "0", enabling this feature. If the built-in siren driver is NOT to be used, take the following procedure. First,
remove the jumper marked voltage/siren on the PC board. Next, program a "1" in location 132. Finally, replace the
jumper in the voltage position. Terminals 21 & 22 will now output 1 Amp at 12VDC.
LOCATION 133: L.E.D. EXTINGUISH FEATURE
Keypad LEDs (excluding the A.C. LED) will be extinguished after 60 seconds of keypad inactivity, if a "1" is
programmed in location 133. The LEDs will become illuminated immediately upon a keypress or alarm condition.
LOCATION 134: ENTERING THE NUMBER OF DIAL ATTEMPTS
Location 134 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will try for the
appropriate phone number(s) before ending the notification process. If this location contains an "8", the communicator
will make eight attempts to the first number, and then eight attempts to a second number, if a second number is
programmed as backup.
LOCATION 135: POWER UP CONDITION
If a "1" is programmed in location 135, the Ranger 8980 will power-up disarmed if there is a total power shutdown and
battery failure. If a "2" is programmed in this location, it will power up armed. If this location contains a "0", the Ranger
8980 will power up in the condition it was in at power down. A watchdog circuit reset will cause the Ranger 8980 to
reset to the selected condition.
LOCATION 136: POWER UP DELAY
If a "1" is programmed in location 136, the Ranger 8980 will not delay 60 seconds before accepting open or short
inputs from any zone. If a "0" is programmed, sensors on all zones are allowed 60 seconds to stabilize at power-up.
After 60 seconds, the Ranger will once again accept loop opens or shorts as an alarm condition. This 60-second
period will also be initiated after exiting the program mode, or a watchdog circuit reset condition.
LOCATION 137: IMMEDIATE RESTORE BY ZONE
If a "1" is programmed in location 137, restoral signals will follow the restore condition and report restores immediately
after the condition has unfaulted. A non-extended format will not send a restore message until all zones and trouble
conditions have restored. If this location contains a "0", the restore signal or signals will be reported only after siren
timeout.
Prodotti e manuali riguardandi Telecomandi Side-Power 8980
Telecomandi Side-Power RC-10E Manuale Utente
(9 pagine)
(9 pagine)
Telecomandi Side-Power RC-10E Manuale Utente
(20 pagine)
(20 pagine)
Telecomandi Side-Power RC-10E Specifiche
(32 pagine)
(32 pagine)
Telecomandi Side-Power RC-10E Manuale Utente
(12 pagine)
(12 pagine)
Telecomandi Side-Power 8980 Manuale Utente
(12 pagine)
(12 pagine)
Telecomandi Side-Power 8980 Manuale Utente
(12 pagine)
(12 pagine)
Telecomandi Side-Power 8981 Manuale Utente
(11 pagine)
(11 pagine)
Pioneer CNSD 400 FM manuály
Uživatelské manuály a uživatelské příručky pro CD přehrávače Pioneer CNSD 400 FM.
Poskytujeme manuály pdf Pioneer CNSD 400 FM ke stažení zdarma podle typů dokumentů:
Commenti su questo manuale